Contact us

Mactron Technology.

Tel: +86-769-2638 4404

Fax: +86-769-2638 4091  

Email: sales@co2-lasers.com   

      mactrontech@yahoo.com

Skype: mactrontech

Our New Site:

www.mactron-tech.com

Mactron Aliexpress Store

Mactron is The Audited Supplier from Made-In-China 

DPES Laser Engraving Machine EXPO Invitation

Tel: +86-769-2638 4404
Fax: +86-7

Co2 Laser Power Supply (150 watts)

Co2 Laser Power Supply (150 watts)

150W Co2 Laser Power Supply is special designed for 150W-180W Co2 glass laser tube, adopts high frequency design, top quality IC parts for major parts to ensure high performance and lifetime, widely used for kinds of industrial laser cutting machine, laser flat bed cutting machine, very high life time and high cost performance. 

 

1. The main features of the Laser Power Supply 150 Watt:

 

* Stable performance:

Each Laser Power Supply Circuit have been much more rigorous testing procedures, under full load high temperature (52~55 degrees celsius) 24 hours of aging, to ensure the stability of each power supply.

* Output voltage, current large (AC220V input, the maximum output current up to 40mA, voltage up to 50kv)

* Improve the laser power: 2000mm laser tube and supporting the use of peak laser power can reach 150W, the average power of 130W.

* Circuit design is reasonable, It’s a high-end laser engraving machine, cutting machine the best choice. At the same time, significantly extend the life of the laser tube.

* Good compatibility:

Can adapt to a number of manufacturers of CO2 laser tube, but also has strong adaptability and fast response, engraving, cutting effect of a good advantage.

* Control is simple:

Select high or low level control, the use of TTL-level control of the laser can start and stop. At the same time increase the protection switch, testing is through the external water and ventilation.

Laser power control is simple, you can use 0 ~ 5V analog signal control the size of the laser power, you can also use the PWM (pulse width modulation) signal to be controlled.* Protection function:

Power supply itself has open circuit protection, a good grounding in the case of protection, the power supply to short-term work in the open state, so to avoid the laser tube burst due to the damage caused by laser power supply, thereby enhancing the laser power supply of life.

* Special Features: (optional addition)

Power users do not need to open the shell, you can simply determine the laser power is working to distinguish between the failure of laser tube or power supply failure, it is very good for Laser Power Supply Repair.

 

2. Specifications:

 

Model

Parameters

150W Laser power

Input

Input Voltage

AC220V±10% (Need  AC110V products, ordering need indicate)

AC frequency

47 - 440HZ

Cold-state Surge Current

≤60A(AC220V input)

≤30A(AC110V input)

Leakage current

≤0.7mA(AC220V input) ≤0.4mA(AC110V input)

Output

Maximum output voltage

 

DC50KV

Maximum output current

DC40mA(depending on the laser tubes of different manufacturers)

Efficiency

≥90%( Full load)

Response speed

≤ 1ms

Control Interface

TTL multilevel switching control, effective level can be high and low selection (see control wiring diagram)

 

Insulation

Input--output

AC 1500V 1 minutes ≤10 mA

Input--shell

AC 1500V 1 minutes ≤10 mA

Output--shell

Connection

Insulation Resistance

≥50MΩ(DC500V)

Environmental
Requested

 

Working temperature

-10℃ - 50℃

Storage of temperature

 

-20℃ - 75℃

Relative Humidity

Maximum 85% RH (non-condensing)

 

Altitude

 

100,000 feet of work 200,000 feet of storage, does not work

Cooling methods

Forced air cooling (fan cooling)

 

Dimensions (L*W*H)

350mm*235mm*97mm